各位大俠,小弟現正做一電源,主電源部分為一半橋電路,輸出功率600w.前級有加PFC.半橋控制芯片為MC34025,PFC部分已調好
現出現如下問題,即從波形上看發現在佔空比較小時,功率變壓器副邊不再是方波而是壘加了一些正弦波,控制TL431環路有跳變的波形輸出(從光偶處測得)
功率變壓器發出很大的叫聲.此時僅能帶120W左右的負載,再加負載是輸出電壓掉到十幾伏.
請各位幫忙分析原因,不勝感激.....
原理圖
1086397871.pdf
主變壓器為PQ4040 初級20T次級4+4T輸出34V全波整流.
各點波形如下,我選貼出變化比較顯的波形(較不正常)
還有一點,空載剛開機時變壓器叫聲較小特別是長時間斷電後再開機而連續開機則有一樣大的叫聲.
以下波形為空載時測得
主變壓器副邊波形
![](http://u.dianyuan.com/bbs/u/18/1086397957.bmp)
500) {this.resized=true; this.width=500; this.alt='这是一张缩略图,点击可放大。\n按住CTRL,滚动鼠标滚轮可自由缩放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/18/1086397957.bmp');}" onmousewheel="return imgzoom(this);">
主變壓器原邊中點波形(測兩只mosfet與地之間)
![](http://u.dianyuan.com/bbs/u/18/1086398024.bmp)
500) {this.resized=true; this.width=500; this.alt='这是一张缩略图,点击可放大。\n按住CTRL,滚动鼠标滚轮可自由缩放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/18/1086398024.bmp');}" onmousewheel="return imgzoom(this);">
開關管下管柵极波形
![](http://u.dianyuan.com/bbs/u/18/1086398109.bmp)
500) {this.resized=true; this.width=500; this.alt='这是一张缩略图,点击可放大。\n按住CTRL,滚动鼠标滚轮可自由缩放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/18/1086398109.bmp');}" onmousewheel="return imgzoom(this);">
mc34025驅動輸出端波形
![](http://u.dianyuan.com/bbs/u/18/1086398159.bmp)
500) {this.resized=true; this.width=500; this.alt='这是一张缩略图,点击可放大。\n按住CTRL,滚动鼠标滚轮可自由缩放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/18/1086398159.bmp');}" onmousewheel="return imgzoom(this);">